guide-pro2
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
guide-pro2 [2021/02/28 17:25] – [Brake light mode] tidings | guide-pro2 [2022/01/15 01:36] (current) – external edit 127.0.0.1 | ||
---|---|---|---|
Line 9: | Line 9: | ||
This tab links straight to Google Play store. It is suggested to use SH utility for flashing the herein generated firmware. | This tab links straight to Google Play store. It is suggested to use SH utility for flashing the herein generated firmware. | ||
- | In case your device does not come with Google Play or Google Service Framework installed, you can download the apk here: [[https://utility.cfw.sh/apk|https://utility.cfw.sh/apk]] | + | In case your device does not come with Google Play or Google Service Framework installed, you can download the apk here: [[https://scooterhack.in/utilityapk|https://scooterhack.in/utilityapk]] |
===== Presets ===== | ===== Presets ===== | ||
Line 40: | Line 40: | ||
===== Power and Speed ===== | ===== Power and Speed ===== | ||
- | ==== Current limit ==== | + | {{https:// |
- | (Currently WIP, will be added once stable channel | + | ==== Estimated draw ==== |
+ | |||
+ | Current in the following rows should be thought as torque. More amperage means more torque, but also more stress on the components and motor, usually less range on single charge. It is suggested to start from factory values and proceed up only if necessary. 25A on Sport mode is already high enough that the motor cannot exert this level of torque for long without overheating. Bear in mind that the motor case temperature are only a fraction of the heat generated by coils, which are usually 50-60C hotter than the case. | ||
+ | |||
+ | **Estimated draw** is the ' | ||
+ | |||
+ | **Current limit** was previously known as //phase current limit //. This is the peak envelope power on the ABC phases, measured by the ESC itself. __Treat this as hard limit, and the estimated draw as soft limit.u When unsure, you can set this to 2-3 times of the estimated draw. | ||
+ | |||
+ | **Recommended values (if you don't know what to do)** | ||
+ | |||
+ | * Sport - Estimated 25A, Limit 65A | ||
+ | * Drive - Estimated 17A, Limit 65A | ||
+ | * Eco - Estimated 10A | ||
{{https:// | {{https:// | ||
+ | |||
==== Max speed ==== | ==== Max speed ==== | ||
Line 62: | Line 75: | ||
* In direct power mode, your scooter will try to reach the maximum speed possible, until set current limits are reached. | * In direct power mode, your scooter will try to reach the maximum speed possible, until set current limits are reached. | ||
* DPC mode can be disabled entirely, enabled through boot sequence with brake lever pressed (press the brake lever while turning on the scooter, and keep it pressed for 2 seconds until it’s fully on), or always enabled. | * DPC mode can be disabled entirely, enabled through boot sequence with brake lever pressed (press the brake lever while turning on the scooter, and keep it pressed for 2 seconds until it’s fully on), or always enabled. | ||
+ | * Since 5th March, there' | ||
* There are two response settings for the throttle – flat and quadratic | * There are two response settings for the throttle – flat and quadratic | ||
* Flat makes the throttle response linear – e.g. throttle at 60% results in 60% of the max current set | * Flat makes the throttle response linear – e.g. throttle at 60% results in 60% of the max current set | ||
Line 108: | Line 122: | ||
* Reversed - No strobe on braking, strobe on drive | * Reversed - No strobe on braking, strobe on drive | ||
* Strobe - Always strobe | * Strobe - Always strobe | ||
- | |||
==== Brake light flash frequency ==== | ==== Brake light flash frequency ==== |
guide-pro2.1614533122.txt.gz · Last modified: 2022/01/15 01:33 (external edit)