nberrorcodes
Differences
This shows you the differences between two versions of the page.
| Next revisionBoth sides next revision | |||
| nberrorcodes [2019/09/28 23:17] – created lothean | nberrorcodes [2019/09/28 23:40] – lothean | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | Ninebot ESx/Max Error Codes | + | ====== |
| + | |||
| + | ^Code ^Description | ||
| + | |10|No communication with BLE board |Check the connection between dashboard and ESC, [[https:// | ||
| + | |11|Motor phase A current out of range | | | ||
| + | |12|Motor phase B current out of range| | | ||
| + | |13|Motor phase C current out of range| | ||
| + | |14|Throttle handle position out of range|Throttle might be stuck, faulty or disconnected| | ||
| + | |15|Brake handle position out of range|Brake handle might be stuck, faulty or disconnected| | ||
| + | |18|Motor Hall sensors stuck at 0/1|Check 2×4 connector between ESC and motor| | ||
| + | |19|Internal battery voltage out of range| | | ||
| + | |20|External battery voltage out of range| | | ||
| + | |21|No communication with internal BMS|Check data connector between internal battery and ESC, replace battery| | ||
| + | |22|Internal BMS config invalid|Replace internal BMS or battery| | ||
| + | |23|Internal BMS not activated (has default S/ | ||
| + | |24|Supply voltage out of range| | | ||
| + | |26|Flash save error|[[https:// | ||
| + | |27|ESC config invalid|[[https:// | ||
| + | |32|No communication with IoT device|Leave that rental scooter where it belongs| | ||
| + | |35|ESC not activated, has default S/ | ||
| + | |36|2+4 connector failure or external battery charging wire failure.| | | ||
| + | |37|Charging base failure or built-in battery charging wire failure.| | | ||
| + | |38|Charging overcurrent|Incorrect power supply| | ||
| + | |39|Internal battery overheat| | | ||
| + | |40|ESC overheat| | | ||
| + | |41|External battery overheat| | | ||
| + | |42|No communication with external BMS|Inspect external battery connectors, tighten up external battery screws| | ||
| + | |43|External BMS config invalid|Replace external BMS or battery| | ||
| + | |44|External BMS not activated (has default S/ | ||
| + | |45|Internal BMS deep cell discharge| | | ||
| + | |46|External BMS deep cell discharge| | | ||
| + | |49|Internal BMS firmware version mismatch|Change internal BMS firmware version| | ||
| + | |50|External BMS firmware version mismatch|Change external BMS firmware version| | ||
| + | |||
| + | [[https:// | ||
| + | |||
| + | \\ | ||
| - | ^ Code ^ Description | ||
| - | | 10 | No communication with BLE board | Check the connection between dashboard and ESC, [[https:// | ||
| - | | 11 | Motor phase A current out of range | | | ||
| - | | 12 |Motor phase B current out of range | | | ||
| - | | 13 |Motor phase C current out of range | | | ||
| - | | 14 |Throttle handle position out of range | Throttle might be stuck, faulty or disconnected | | ||
| - | | 15 |Brake handle position out of range | Brake handle might be stuck, faulty or disconnected | | ||
| - | | 18 |Motor Hall sensors stuck at 0/1 | Check 2x4 connector between ESC and motor | | ||
| - | | 19 |Internal battery voltage out of range | | | ||
| - | | 20 |External battery voltage out of range | | | ||
| - | | 21 |No communication with internal BMS | Check data connector between internal battery and ESC, replace battery | | ||
| - | | 22 |Internal BMS config invalid | Replace internal BMS or battery | | ||
| - | | 23 |Internal BMS not activated (has default S/N) | Replace internal BMS or battery | ||
| - | | 24 |Supply voltage out of range | | | ||
| - | | 26 |Flash save error | [[https:// | ||
| - | | 27 |ESC config invalid |[[https:// | ||
| - | | 24 |Supply voltage out of range | | | ||
| - | | 24 |Supply voltage out of range | | | ||
| - | | 24 |Supply voltage out of range | | | ||
| - | | 24 |Supply voltage out of range | | | ||
| - | | 24 |Supply voltage out of range | | | ||
| - | | 24 |Supply voltage out of range | | | ||
nberrorcodes.txt · Last modified: 2022/01/15 01:36 by 127.0.0.1