User Tools

Site Tools


nberrorcodes

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
nberrorcodes [2019/10/27 20:19] lotheannberrorcodes [2022/01/15 01:36] (current) – external edit 127.0.0.1
Line 1: Line 1:
 ====== Ninebot ESx/Max Error Codes ====== ====== Ninebot ESx/Max Error Codes ======
  
-^Code  ^Description  ^Additional information +^Code  ^Description  ^Additional information  ^Severity  ^Level  | 
-|10|No communication with BLE board  |Check the connection between dashboard and ESC[[https://www.scooterhacking.org/forum/viewtopic.php?f=6&t=40|try to flash ESC with ST-Link]] (ESx)| +|10|Communication Failure between Dashboard and ESC.  |Check the connection between dashboard and ESC. \\ ESC is possibly soft-bricked; try to flash ESC with ST-Link ([[https://www.scooterhacking.org/forum/viewtopic.php?f=6&t=40|ESx]], [[https://www.scooterhacking.org/forum/viewtopic.php?f=26&t=213|Max]])|System error|3
-|11|Motor phase A current out of range  | | +|11|Motor phase A current out of range  | |Hardware error|3
-|12|Motor phase B current out of range| | +|12|Motor phase B current out of range| |Hardware error|3
-|13|Motor phase C current out of range|   | +|13|Motor phase C current out of range|   |Hardware error  |3  
-|14|Throttle handle position out of range|Throttle might be stuck, faulty or disconnected| +|14|Throttle handle position out of range|Throttle might be stuck, faulty or disconnected|Hardware error|3
-|15|Brake handle position out of range|Brake handle might be stuck, faulty or disconnected| +|15|Brake handle position out of range|Brake handle might be stuck, faulty or disconnected|Hardware error|3| 
-|18|Motor Hall sensors stuck at 0/1|Check 2×4 connector between ESC and motor; [[https://www.scooterhacking.org/forum/viewtopic.php?f=6&t=174&p=992|attempt fix]]| +|16|Internal Battery change MOS abnormal| |Hardware error|3| 
-|19|Internal battery voltage out of range| | +|17|External battery change MOS abnormal| |Hardware error|3
-|20|External battery voltage out of range| | +|18|Motor Hall sensors stuck at 0/1|Check 2×4 connector between ESC and motor; [[https://www.scooterhacking.org/forum/viewtopic.php?f=6&t=174&p=992|attempt fix]]|Hardware error|3
-|21|No communication with internal BMS|Check data connector between internal battery and ESC, replace battery| +|19|Internal battery voltage out of range| |Hardware error|3
-|22|Internal BMS config invalid|Replace internal BMS or battery; [[https://www.scooterhacking.org/forum/viewtopic.php?f=6&t=173|attempt a fix]]| +|20|External battery voltage out of range| |Hardware error|3
-|23|Internal BMS not activated (has default S/N)|Replace internal BMS or battery; [[https://www.scooterhacking.org/forum/viewtopic.php?f=6&t=173|attempt a fix]]  | +|21|No communication with internal BMS|Check data connector between internal battery and ESC, replace the battery|Battery mod warning|2
-|24|Supply voltage out of range| | +|22|Internal BMS config invalid|Replace internal BMS or battery; [[https://www.scooterhacking.org/forum/viewtopic.php?f=6&t=173|attempt a fix]], or, flash CFW with error raising disabled.|System warning|1
-|26|Flash save error|[[https://www.scooterhacking.org/forum/viewtopic.php?f=6&t=40|Try to flash ESC with ST-Link]] (ESx)replace ESC| +|23|Internal BMS not activated (has default S/N)|Replace internal BMS or battery; [[https://www.scooterhacking.org/forum/viewtopic.php?f=6&t=173|attempt a fix]], or, flash CFW with error raising disabled.  |System warning  |1  | 
-|27|ESC config invalid|[[https://www.scooterhacking.org/forum/viewtopic.php?f=6&t=40|Try to flash ESC with ST-Link]] (ESx)| +|24|Supply voltage out of range| |Battery mod warning|2| 
-|32|No communication with IoT device|Leave that rental scooter where it belongs| +|25|Communication failure during ESC fimware update|Hard-reset scooter|System error|3
-|35|ESC not activated, has default S/N|[[https://www.scooterhacking.org/forum/viewtopic.php?f=6&t=14|for ESx]], [[https://www.scooterhacking.org/forum/viewtopic.php?f=26&t=120|for Max]]| +|26|Flash save error|Try to flash ESC with ST-Link ([[https://www.scooterhacking.org/forum/viewtopic.php?f=6&t=40|ESx]], [[https://www.scooterhacking.org/forum/viewtopic.php?f=26&t=213|Max]]), replace ESC|System error|3| 
-|36|2+4 connector failure or external battery charging wire failure.| | +|27|ESC config invalid (CPUID register might not match STM CPUID)|Change SN using BLE/UART ([[https://bit.ly/ESx-Activation|ESx]], [[https://bit.ly/max-unlock|Max]])|System warning|1| 
-|37|Charging base failure or built-in battery charging wire failure.| | +|28|Motor driver mos up-bridge short circuit|Check motor|Hardware error|3| 
-|38|Charging overcurrent|Incorrect power supply| +|29|Motor driver mos down-bridge short circuit|Check motor|Hardware error|3| 
-|39|Internal battery overheat| | +|31|Program skip error|Try to flash ESC|System error|3
-|40|ESC overheat| | +|32|No communication with IoT device|Leave that rental scooter where it belongs|System error|3
-|41|External battery overheat| | +|35|ESC not activated, has default S/N|[[https://www.scooterhacking.org/forum/viewtopic.php?f=6&t=14|for ESx]], [[https://www.scooterhacking.org/forum/viewtopic.php?f=26&t=120|for Max]]|System warning|1
-|42|No communication with external BMS|Inspect external battery connectors, tighten up external battery screws| +|36|2+4 connector failure or external battery charging wire failure.| |Hardware error|3
-|43|External BMS config invalid|Replace external BMS or battery; [[https://www.scooterhacking.org/forum/viewtopic.php?f=6&t=173|attempt a fix]]| +|37|Charging base failure or built-in battery charging wire failure.| |Hardware error|3
-|44|External BMS not activated (has default S/N)|Replace external BMS or battery; [[https://www.scooterhacking.org/forum/viewtopic.php?f=6&t=173|attempt a fix]]| +|38|Charging overcurrent|Incorrect power supply|Hardware error|3
-|45|Internal BMS deep cell discharge| | +|39|Internal battery overheat| |Hardware error/battery mod warning|2
-|46|External BMS deep cell discharge| | +|40|ESC overheat|Let the scooter cool down / check temperature sensors|Hardware error|3
-|49|Internal BMS firmware version mismatch|Change internal BMS firmware version| +|41|External battery overheat| |Hardware error|3
-|50|External BMS firmware version mismatch|Change external BMS firmware version|+|42|No communication with external BMS|Inspect external battery connectors, tighten up external battery screws|Hardware error|3
 +|43|External BMS config invalid|Replace external BMS or battery; [[https://www.scooterhacking.org/forum/viewtopic.php?f=6&t=173|attempt a fix]]|System warning|1
 +|44|External BMS not activated (has default S/N)|Replace external BMS or battery; [[https://www.scooterhacking.org/forum/viewtopic.php?f=6&t=173|attempt a fix]]|System warning|1
 +|45|Internal BMS deep cell discharge| |Hardware error|3
 +|46|External BMS deep cell discharge| |Hardware error|3| 
 +|47|Internal battery protection board damaged|Replace internal battery or BMS|Hardware error|3| 
 +|48|External battery protection board damaged|Replace external battery or BMS|Hardware error|3
 +|49|Internal BMS firmware version mismatch|Change internal BMS firmware version|System warning|2
 +|50|External BMS firmware version mismatch|Change external BMS firmware version|System warning|2| 
 +|51|BLE firmware incompatible with DRV|Change BLE or DRV firmware|System warning|nd| 
 +|52|BMS firmware incompatible with DRV **(Retail)** / ESC incompatible with battery hatch lock **(Rental)** |Change BMS firmware version **(Retail)** |System warning/Hardware error|nd| 
 +|54|Motor phase error **(Retail)** / ESC/battery hatch lock communication error **(Rental)** |Check motor-related wiring **(Retail)** |Hardware error|nd| 
 +|55|Battery hatch unlocked| |System warning|nd|
  
-[[https://github.com/etransport/ninebot-docs/wiki/ES2ESC#error-codes|Original source]]+nd no data
  
 \\ \\
  
  
nberrorcodes.1572207552.txt.gz · Last modified: 2022/01/15 01:34 (external edit)