User Tools

Site Tools


nberrorcodes

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
nberrorcodes [2019/10/27 21:19]
lothean
nberrorcodes [2020/06/05 22:44] (current)
foxmaster added err 48
Line 1: Line 1:
 ====== Ninebot ESx/Max Error Codes ====== ====== Ninebot ESx/Max Error Codes ======
  
-^Code  ^Description ​ ^Additional information ​ | +^Code  ^Description ​ ^Additional information ​ ​^Severity ​ ^Level ​ | 
-|10|No communication with BLE board  ​|Check the connection between dashboard and ESC[[https://​www.scooterhacking.org/​forum/​viewtopic.php?​f=6&​t=40|try to flash ESC with ST-Link]] (ESx)| +|10|Communication Failure between Dashboard and ESC.  ​|Check the connection between dashboard and ESC. \\ ESC is possibly soft-bricked;​ try to flash ESC with ST-Link ([[https://​www.scooterhacking.org/​forum/​viewtopic.php?​f=6&​t=40|ESx]], [[https://​www.scooterhacking.org/​forum/​viewtopic.php?​f=26&​t=213|Max]])|System error|3
-|11|Motor phase A current out of range  | | +|11|Motor phase A current out of range  | |Hardware error|3
-|12|Motor phase B current out of range| | +|12|Motor phase B current out of range| ​|Hardware error|3
-|13|Motor phase C current out of range| ​  | +|13|Motor phase C current out of range| ​  |Hardware error  |3  ​
-|14|Throttle handle position out of range|Throttle might be stuck, faulty or disconnected| +|14|Throttle handle position out of range|Throttle might be stuck, faulty or disconnected|Hardware error|3
-|15|Brake handle position out of range|Brake handle might be stuck, faulty or disconnected| +|15|Brake handle position out of range|Brake handle might be stuck, faulty or disconnected|Hardware error|3| 
-|18|Motor Hall sensors stuck at 0/1|Check 2×4 connector between ESC and motor; [[https://​www.scooterhacking.org/​forum/​viewtopic.php?​f=6&​t=174&​p=992|attempt a fix]]| +|16|Internal Battery change MOS abnormal| |Hardware error|3| 
-|19|Internal battery voltage out of range| | +|17|External battery change MOS abnormal| |Hardware error|3
-|20|External battery voltage out of range| | +|18|Motor Hall sensors stuck at 0/1|Check 2×4 connector between ESC and motor; [[https://​www.scooterhacking.org/​forum/​viewtopic.php?​f=6&​t=174&​p=992|attempt a fix]]|Hardware error|3
-|21|No communication with internal BMS|Check data connector between internal battery and ESC, replace battery| +|19|Internal battery voltage out of range| ​|Hardware error|3
-|22|Internal BMS config invalid|Replace internal BMS or battery; [[https://​www.scooterhacking.org/​forum/​viewtopic.php?​f=6&​t=173|attempt a fix]]| +|20|External battery voltage out of range| ​|Hardware error|3
-|23|Internal BMS not activated (has default S/​N)|Replace internal BMS or battery; [[https://​www.scooterhacking.org/​forum/​viewtopic.php?​f=6&​t=173|attempt a fix]]  | +|21|No communication with internal BMS|Check data connector between internal battery and ESC, replace ​the battery|Battery mod warning|2
-|24|Supply voltage out of range| | +|22|Internal BMS config invalid|Replace internal BMS or battery; [[https://​www.scooterhacking.org/​forum/​viewtopic.php?​f=6&​t=173|attempt a fix]], or, flash CFW with error raising disabled.|System warning|1
-|26|Flash save error|[[https://​www.scooterhacking.org/​forum/​viewtopic.php?​f=6&​t=40|Try to flash ESC with ST-Link]] (ESx), replace ESC| +|23|Internal BMS not activated (has default S/​N)|Replace internal BMS or battery; [[https://​www.scooterhacking.org/​forum/​viewtopic.php?​f=6&​t=173|attempt a fix]], or, flash CFW with error raising disabled. ​ |System warning ​ |1  | 
-|27|ESC config invalid|[[https://​www.scooterhacking.org/​forum/​viewtopic.php?​f=6&​t=40|Try to flash ESC with ST-Link]] (ESx)+|24|Supply voltage out of range| ​|Battery mod warning|2
-|32|No communication with IoT device|Leave that rental scooter where it belongs| +|26|Flash save error|Try to flash ESC with ST-Link ([[https://​www.scooterhacking.org/​forum/​viewtopic.php?​f=6&​t=40|ESx]], [[https://​www.scooterhacking.org/​forum/​viewtopic.php?​f=26&​t=213|Max]]), replace ESC|System error|3
-|35|ESC not activated, has default S/​N|[[https://​www.scooterhacking.org/​forum/​viewtopic.php?​f=6&​t=14|for ESx]], [[https://​www.scooterhacking.org/​forum/​viewtopic.php?​f=26&​t=120|for Max]]| +|27|ESC config invalid|Try to flash ESC with ST-Link ([[https://​www.scooterhacking.org/​forum/​viewtopic.php?​f=6&​t=40|ESx]], [[https://​www.scooterhacking.org/​forum/​viewtopic.php?​f=26&​t=213|Max]])|System warning|1| 
-|36|2+4 connector failure or external battery charging wire failure.| | +|28|Motor driver mos up-bridge short circuit|Check motor|Hardware error|3| 
-|37|Charging base failure or built-in battery charging wire failure.| | +|29|Motor driver mos down-bridge short circuit|Check motor|Hardware error|3| 
-|38|Charging overcurrent|Incorrect power supply| +|31|Program skip error|Try to flash ESC|System error|3
-|39|Internal battery overheat| | +|32|No communication with IoT device|Leave that rental scooter where it belongs|System error|3
-|40|ESC overheat| | +|35|ESC not activated, has default S/​N|[[https://​www.scooterhacking.org/​forum/​viewtopic.php?​f=6&​t=14|for ESx]], [[https://​www.scooterhacking.org/​forum/​viewtopic.php?​f=26&​t=120|for Max]]|System warning|1
-|41|External battery overheat| | +|36|2+4 connector failure or external battery charging wire failure.| ​|Hardware error|3
-|42|No communication with external BMS|Inspect external battery connectors, tighten up external battery screws| +|37|Charging base failure or built-in battery charging wire failure.| ​|Hardware error|3
-|43|External BMS config invalid|Replace external BMS or battery; [[https://​www.scooterhacking.org/​forum/​viewtopic.php?​f=6&​t=173|attempt a fix]]| +|38|Charging overcurrent|Incorrect power supply|Hardware error|3
-|44|External BMS not activated (has default S/​N)|Replace external BMS or battery; [[https://​www.scooterhacking.org/​forum/​viewtopic.php?​f=6&​t=173|attempt a fix]]| +|39|Internal battery overheat| ​|Hardware error|3
-|45|Internal BMS deep cell discharge| | +|40|ESC overheat| ​|Hardware error|3
-|46|External BMS deep cell discharge| | +|41|External battery overheat| ​|Hardware error|3
-|49|Internal BMS firmware version mismatch|Change internal BMS firmware version| +|42|No communication with external BMS|Inspect external battery connectors, tighten up external battery screws|Hardware error|3
-|50|External BMS firmware version mismatch|Change external BMS firmware version|+|43|External BMS config invalid|Replace external BMS or battery; [[https://​www.scooterhacking.org/​forum/​viewtopic.php?​f=6&​t=173|attempt a fix]]|System warning|1
 +|44|External BMS not activated (has default S/​N)|Replace external BMS or battery; [[https://​www.scooterhacking.org/​forum/​viewtopic.php?​f=6&​t=173|attempt a fix]]|System warning|1
 +|45|Internal BMS deep cell discharge| ​|Hardware error|3
 +|46|External BMS deep cell discharge| ​|Hardware error|3| 
 +|48|External battery protection board damaged|Replace external battery or BMS|Hardware error|3
 +|49|Internal BMS firmware version mismatch|Change internal BMS firmware version|System warning|2
 +|50|External BMS firmware version mismatch|Change external BMS firmware version|System warning|2|
  
 [[https://​github.com/​etransport/​ninebot-docs/​wiki/​ES2ESC#​error-codes|Original source]] [[https://​github.com/​etransport/​ninebot-docs/​wiki/​ES2ESC#​error-codes|Original source]]
nberrorcodes.1572207562.txt.gz · Last modified: 2019/10/27 21:19 by lothean